Leftenan (Udara) Khoo's Skyhawk, Kuantan, June 1990

Leftenan (Udara) Khoo’s Skyhawk, Kuantan, June 1990

photo3
Nordic Con 2015 Gold

Nordic Con 2015 Gold


This project started more than 8 years ago. In a casual email exchange with my childhood friend Capt. Khoo, formerly of the Royal Malaysian Air Force, I had found out that from the mid-1980’s through the early 90’s, he had been a pilot of Malaysia’s A4-PTM Skyhawks in the ground attack role. The RMAF 6 Skuadron was stationed in Kuantan Air Base on the east coast of the Malay Peninsular. Since then, I had planned to build his personal aircraft as part of my collection of Malaysian-themed model builds.

Gallery:

IMG_0048

IMG_0047

IMG_0075

IMG_0049

IMG_0072

IMG_0069

IMG_0067

IMG_0059

IMG_0058

IMG_0053

IMG_0077

IMG_0079

IMG_0081

IMG_0083

IMG_0949

The basic kit that I had chosen was the A4-C Skyhawk kit by Hobby Craft because the set already had Malaysian Skyhawk markings and parts for the avionics “hump”. As it turned out later, I could not use most of those markings because they portrayed an earlier color scheme (sand-middle green-dark green) whereas then Lt. Khoo’s aircraft call-signed FROG was in the later Olive Drab-Jungle Green color scheme. I first picked up the kit back in 2005, and then over the years, accumulated the Aires resin cockpit set, Aires wheel wells and a photoetched fret from Eduard.

IMG_0951

The Aires cockpit set was incredibly detailed and was a joy to paint. It stood in stark contrast to the pitifully bare cockpit details from the original Hobby Craft kit. The only thing I substituted was the instrument panel that I replaced with the Zoom colored panel from Eduard.

IMG_0954IMG_0958

It’s always good to listen to the pilot! Before I finalized the cockpit, I asked my friend about the cockpit colors and he corrected my initial Grey color scheme for the seat and belts to the green color scheme that you can see on the right. That front office is always important in any aircraft project so I had to get it right.

IMG_0959IMG_0967

Directly beneath that cockpit tub was the front tricycle wheel well. I found the fit to be pretty poor and it left a huge gaping hole between the well and the fuselage. I used Evergreen plastic strips to fill in the huge gap. This will be the topic of a future Tutorial page.

IMG_0964IMG_0965

Next, I marked out the portions of the wheel wells on the underside wing section and carefully cut them out using my modelling fine saw and X-acto knife.

IMG_0971

Once the cut sites were properly filed and cleaned, I replaced the sections with resin parts from Aires. Like the cockpit, the amount of detail in the resins parts are a huge improvement over the basic kit parts. The fit had to be just right and there was a lot of part-thinning and shaving needed in order for the wing halves to close together properly. Much patience needed with a lot of dry fitting and not for the faint-of-heart.

IMG_0968

The fuselage halves get put together with the cockpit tub nicely fitted in.

IMG_0969

To prevent this aircraft from being a tail sitter, I added about 30 grams of lead shot into the nose cone.

IMG_0970

The wing section was carefully glued onto the fuselage. The wing root joints were pretty good on both sides and did not require any major gap filling of the seams.

IMG_0983

In preparation for the spray booth, I masked off the windshield and canopy sections.

IMG_0980
IMG_0982
IMG_0984

The initial undercoat preparation sequence starts with Gloss Insignia White FS12875 for the wheel wells, then followed by Tamiya NATO Black lines for the under-shading of the panel lines, followed by Flat Black FS37038 for the anti-glare panel and nose cone.

IMG_0986IMG_0989

Olive Drab FS34087 is lightened with 20% Flat White as the first tone of the camouflage and applied uniformly including the underside of the aircraft. This is followed by Dark Green FS34079 darkened with 30% Flat Black applied freehand for that feathered pattern found on the Malaysian tropical 2-tone ground-attack scheme. Once dried, a gloss varnish was applied to prepare the aircraft for decal application.

IMG_0991
IMG_0993

As I had mentioned earlier, the decals from the kit were not correct for the particular aircraft serial number M32-23. Khoo’s aircraft had square national insignia markings instead of the round ones from an earlier version. His aircraft also sported the red-and-black checkered bands on both sides of the fuselage under the cockpit. I printed these decals from my own artwork. The 6 Skuadron’s marking of a diving eagle with red thunderbolts seen on the tail were obtained from another decal sheet for the Hawk Mk. 1 kit. A layer of satin varnish was then applied to blend the decals with the paint work. Weathering was done using oil paint wash mix of Payne’s Grey + Burnt Umber.

IMG_0992
IMG_0995

I proceeded to build the tricycle landing gear parts while the aircraft paintwork was drying. All the parts are painted gloss white like the wheel wells with bright silver for the hydraulic cylinders. Black wire was used to simulate the brake lines. The wheels were given the heat treatment to flatten the tires for the weighted look. Once fixed, the aircraft finally has its own “legs” and happily, not a tail sitter!

IMG_0999

The final details for the underside were added at this stage. The aircraft carried two drop tanks, and a pair of rocket launchers (the ones that look like salt shakers) that I scavenged from my spare part box. The kit only supplied Zuni rocket launchers that were not used in the actual photograph of the aircraft.

IMG_1002
IMG_1007

I scratch-built the ladder used with the Skyhawk with Evergreen plastic square and rectangular rods.Just like the real thing, the ladder is supported with a rod inserted into a hole in the side of the aircraft. Once the final details are added on the aircraft (canopy, navigation lights, pitot tubes), the Jungle Scooter is ready to roar into the tropical skies.

Paul Ooi Modelworks is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.