Morning of 19th June 2010, Nawa District in Helmand Province, Afghanistan

Morning of 19th June 2010, Nawa District in Helmand Province, Afghanistan

IMG_0033

IMG_0021

Rear compartment detail: MRE boxes and bottled water pack

Rear compartment detail: MRE boxes and bottled water pack

Cat tails in the canal

Cat tails in the canal

IMG_0019

The badge is that of the 3rd Marines Regiment

The badge is that of the 3rd Marines Regiment

IMG_0005

Detail of the rear suspension and brake lines

Detail of the rear suspension and brake lines

IMG_0002

IMG_0035

IMG_0025

IMG_0030

IMG_0031

IMG_0023

Actual shot of the Mine Roller

Actual shot of the Mine Roller

IMG_0022

165389_1530795191233_1275330105_31250416_4522254_n

Part 1 of this project was centered around the M-ATV vehicle, and this second part discusses the scratch building of the USMC Panama City Mine Roller. This particular anti-mine device has a superficial similarity to the SPARK Mine Rollers but upon closer examination, has a very different structure. At the time of this post, there are no kits of the Panama City Mine Roller. I obtained a SPARK MIne roller kit to get some resin parts like the hydraulic cylinders, road wheel brackets and spotlights.

From what I could get from checking online sources, the Panama City is a USMC home-grown design based on the hard-earned lessons from the ten years of campaigning in Iraq and Afghanistan. The design is less complicated than the SPARK designs and can be more easily field-maintained. Using commonly available items like tire road wheels also help reduce logistic issues. It seems that this contraption has been adopted by several other allied countries.

IMG_0949

From photographs of the mine roller and scaling the parts to relative features of the MRAP, I was able to build the basic A-shaped frame that forms the main body of the device. The frame is made from Evergreen plastic stock, using C-section and I-beam rods. I made several dry runs by arranging the sections and comparing their positions to the front of the MRAP chassis.

IMG_0952

The mine roller has several brackets for towing/lifting and these were machined from flat card stock, piereced with a mini-drill, and then sanded to shape.

IMG_0953
IMG_0954

The front portion of the mine roller is built with a cross beam that I also took from the SPARK kit. I removed approximately 2 mm from each end to size the width of the beam down. The steering head is a box-shaped contraption built with Evergreen stock, as were the right and left hand platforms. These platforms provide the supports for the weight plates that are used to simulate the full weight of an actual vehicle. The boundary brackets are made from brass wires bent to shape.

IMG_0955

The wheel carriages are cut into shape from black plastic card stock and then attached with the wheel brakcets from the SPARK kit. Because the SPARK kit wheels were smaller diameter solid wheels, I had to remove the original spoke arms and scratch build new ones for the tires used by the Panama City Mine Roller.

IMG_0956

I primed all the main components with primer grey, followed by the Marines Gulf Sand, similar to the M-ATV.

IMG_0957

Once properly dried, I attached the road wheels. These were obtained from resin road wheels for WW2 jeeps. Note how the wheels have this staggered appearance with the two middle ones being slight ahead of the 2 out ones.

IMG_0958

While all these parts are drying, I checked to make sure that the yoke assembly that connect the mine roller to the front of the M-ATV correctly align with the main A-frame as well once attached.

IMG_0960

Once the sections are properly dry, it is time to unite all 5 sections of the mine roller together.

IMG_0961

It is only with the main structure properly built then I started to attach the finer fragile parts, like the two hydraulic cylinders along the A-frame of the mine roller.

IMG_0962

Next, the two front rows of spotlights are attached to the top fenders edging the left and right platforms.

IMG_0964

Finally “hydraulic lines” are added to the assembly. After these have properly dried, I gave the entire mine roller assembly a oil paint wash of Paine’s Grey. Once dried, the Mine roller is ready to be attached to the M-ATV MRAP. A final dusting of light buff spray helps to “dust-up” the mine roller to make it look like it has had a dusty morning rolling along the highway.

IMG_0980

IMG_0979

Paul Ooi Modelworks is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.